A thin film transistor liquid crystal display (TFT-LCD) is a variant of liquid crystal display (LCD) which uses thin film transistor (TFT) technology to improve image quality (e.g. addressability, contrast). TFT LCD is one type of active matrix LCD, though all LCD-screens are based on TFT active matrix addressing. TFT LCDs are used in television sets, computer monitors, mobile phones and computers, personal digital assistants, navigation systems, projectors, etc.Construction
Small liquid crystal displays as used in calculators and other devices have direct driven image elements – a voltage can be applied across one segment without interfering with other segments of the display. This is impractical for a large display with a large number of picture elements (pixels), since it would require millions of connections - top and bottom connections for each one of the three colors (red, green and blue) of every pixel. To avoid this issue, the pixels are addressed in rows and columns which reduce the connection count from millions to thousands. If all the pixels in one row are driven with a positive voltage and all the pixels in one column are driven with a negative voltage, then the pixel at the intersection has the largest applied voltage and is switched. The problem with this solution is that all the pixels in the same column see a fraction of the applied voltage as do all the pixels in the same row, so although they are not switched completely, they do tend to darken. The solution to the problem is to supply each pixel with its own transistor switch which allows each pixel to be individually controlled. The low leakage current of the transistor prevents the voltage applied to the pixel from leaking away between refreshes to the display image. Each pixel is a small capacitor with a layer of insulating liquid crystal sandwiched between transparent conductive ITO layers.
The circuit layout of a TFT-LCD is very similar to that of a DRAM memory. However, rather than fabricating the transistors from silicon formed into a crystalline wafer, they are made from a thin film of silicon deposited on a glass panel. Transistors take up only a small fraction of the area of each pixel; the rest of the silicon film is etched away to allow light to pass through.
The silicon layer for TFT-LCDs is typically deposited using the PECVD process from a silane gas precursor to produce an amorphous silicon film. Polycrystalline silicon (frequently LTPS, low-temperature poly-Si) is sometimes used in displays requiring higher TFT performance. Examples include high-resolution displays, high-frequency displays or displays where performing some data processing on the display itself is desirable. Amorphous silicon-based TFTs have the lowest performance, polycrystalline silicon TFTs have higher performance (notably mobility), and single-crystal silicon transistors are the best performers.
Types
TN + film
The inexpensive 'TN (twisted nematic) + film' display is the most common consumer display type. The pixel response time on modern TN panels is sufficiently fast to avoid the shadow-trail and ghosting artifacts of earlier production. The fast response time has been emphasised in advertising TN displays, although in most cases this number does not reflect performance across the entire range of possible color transitions. Response times were quoted for an ISO standard black-to-white transition and did not reflect the speed of much more common transitions from one shade of grey to another. More recent use of RTC (Response Time Compensation – Overdrive) technologies has allowed manufacturers to significantly reduce grey-to-grey (G2G) transitions, without significantly improving the ISO response time. Response times are now quoted in G2G figures, with 4ms and 2ms now being commonplace for TN Film based models. The good response time and low cost has led to the dominance of TN in the consumer market.
The TN display suffers from limited viewing angles, especially in the vertical direction. For colour representation many panels use 6 bits per colour, instead of 8, and are consequently unable to display the full 24-bit truecolor (16.7 million colour shades) available from modern graphics cards. These panels can display interpolated 24-bit color using a dithering method which combines adjacent pixels to simulate the desired shade. They can also use FRC (Frame Rate Control), which quickly cycles pixels over time to simulate a given shade. These color simulation methods are noticeable to most people and bothersome to some[citation needed]. FRC tends to be most noticeable in darker tones, while dithering appears to make the individual pixels of the LCD visible. Overall, color reproduction and linearity on TN panels is poor. Shortcomings in display color gamut (often referred to as a percentage of the NTSC 1953 color gamut) are also due to backlighting technology. It is not uncommon for displays with CCFL (Cold Cathode Fluorescent Lamps)-based lighting to range from 40% to 76% of the NTSC color gamut, whereas displays utilizing white LED backlights may extend past 100% of the NTSC color gamut – a difference quite perceivable by the human eye.
The transmittance of a pixel of an LCD panel typically does not change linearly with the applied voltage,[1] and the sRGB standard for computer monitors requires a specific nonlinear dependence of the amount of emitted light as a function of the RGB value.
IPS
IPS (in-plane switching) was developed by Hitachi in 1996 to improve on the poor viewing angles and color reproduction of TN panels. Most panels also support true 8-bit per channel color. These improvements came at the cost of a slower response time, initially about 50ms. IPS panels were also extremely expensive. A partial list of LCDs that utilize IPS can be found at PcHardwareHelp.
IPS has since been superseded by S-IPS (Super-IPS, Hitachi in 1998), which has all the benefits of IPS technology with the addition of improved pixel refresh timing. Though color reproduction approaches that of CRTs, the dynamic range is lower. S-IPS technology is widely used in panel sizes of 20" and above. LG.Philips remain two of the main manufacturers of S-IPS based panels.
MVA
MVA (multi-domain vertical alignment) was originally developed in 1998 by Fujitsu as a compromise between TN and IPS. It achieved pixel response which was fast for its time, wide viewing angles, and high contrast at the cost of brightness and color reproduction. Modern MVA panels can offer wide viewing angles (second only to S-IPS technology), good black depth, good color reproduction and depth, and fast response times due to the use of RTC technologies. There are several "next-generation" technologies based on MVA, including AU Optronics' P-MVA and A-MVA, as well as Chi Mei Optoelectronics' S-MVA.
Analysts predicted that MVA would dominate the mainstream market, but the cheaper and slightly faster TN overtook it. MVA's pixel response times rise dramatically with small changes in brightness. Cheaper MVA panels can use dithering and FRC.
PVA
PVA (patterned vertical alignment) and S-PVA (super patterned vertical alignment) are alternative versions of MVA technology offered by Samsung. Developed independently, they offer similar features to MVA, but with higher contrast ratios of up to 3000:1. Less expensive PVA panels often use dithering and FRC, while S-PVA panels all use at least 8 bits per color component and do not use color simulation methods. Some newer S-PVA panels offered by Eizo offer 10-bit color internally, which enables gamma and other corrections with reduced color banding. PVA and S-PVA offer good black depth and wide viewing angles and S-PVA also offers fast response times using modern CRT technologies.
CPA
CPA (Continuous Pinwheel Alignment) was developed by Sharp.
Electrical interface
External consumer display devices like a TFT LCD mostly use an analogue VGA connection, while newer, more expensive models mostly feature a digital interface like DVI, HDMI, or DisplayPort as well.
Inside an external display device there is a controller board that will convert VGA, DVI, HDMI, CVBS etc. to digital RGB at native resolution that the display panel can make use of. In a laptop the graphics chip will directly produce a signal suitable for connection to the builtin TFT. A control mechanism for the backlight is usually included on the same controller board.
The lowlevel interface of STN, DSTN, or TFT display panels use either single ended TTL 5V or TTL 3.3V that transmits Pixel clock, Horizontal sync, Vertical sync, Digital red, Digital green, Digital blue in parallel. Some models also feature input/display enable, horizontal scan direction and vertical scan direction signals.
New and large (>15") TFT displays often use LVDS or TMDS signaling that is the same as the parallel interface but will put control and RGB bits into a number of serial transmission lines synchronized to a clock at 1/3 of the data bitrate.
Backlight intensity is usually controlled by varying a few volts DC to the backlight highvoltage (1.3kV) DC-AC inverter. It can also be controlled by a potentiometer or be fixed. Some models use PWM signal for intensity control.
The bare display panel will only accept a video signal at the resolution determined by the panel pixel matrix designed at manufacture. Some screen panels will ignore colour LSB bits to ease interfacing (8bit->6bit/colour).
The factors why laptop displays can't be reused directly with an ordinary computer graphics card or as a television, is mainly because it lacks a hardware rescaler (often using some discrete cosine transform) that can resize the image to fit the native resolution of the display panel. With analogue signals like VGA the display controller also needs to perform a highspeed analog to digital conversion. With digital input signals like DVI or HDMI some simple bitstuffing is needed before feeding it to the rescaler if input resolution doesn't match the display panel resolution. For CVBS or "TV" usage a tuner and colour decode and transform is needed as well.
Safety
The liquid crystals inside the display are poisonous and must not be ingested or brought into contact with skin. Spills from a cracked display should be washed off immediately with soap and water.
NOTE:
没有评论:
发表评论